Introduction Notes on Modular Sound Drivers and Soundcore Wade Hampton 6/30/1999 Purpose: ======== This document provides some general notes on the modular sound drivers and their configuration, along with the support modules sound.o, soundlow.o and soundcore.o. Note, some of this probably should be added to the Sound-HOWTO! Copying: ======== none History: ======== 0.1.0 11/20/1998 First version, draft 1.0.0 11/1998 Alan Cox changes, incorporation in 2.2.0 as /usr/src/linux/Documentation/sound/Introduction 1.1.0 6/30/1999 Second version, added notes on making the drivers, added info on multiple sound cards of similar types,] added more diagnostics info, added info about esd. added info on OSS and ALSA. Modular Sound Drivers: ====================== Thanks to the GREAT work by Alan Cox (alan@lxorguk.ukuu.org.uk), [And Oleg Drokin, Thomas Sailer, Andrew Veliath and more than a few others - not to mention Hannu's original code being designed well enough to cope with that kind of chopping up](Alan) the standard Linux kernels support a modular sound driver. From Alan's comments in linux/drivers/sound/README.FIRST: The modular sound driver patches were funded by Red Hat Software (www.redhat.com). The sound driver here is thus a modified version of Hannu's code. Please bear that in mind when considering the appropriate forums for bug reporting. The modular sound drivers may be loaded via insmod or modprobe. To support all the various sound modules, there are three general support modules that must be loaded first: soundcore.o: Top level handler for the sound system, provides a set of functions for registration of devices by type. soundlow.o: Low-level sound drivers which are not part of OSS/Lite (Open Sound System), including SB32/AWE synthesizer, etc. sound.o: Common sound functions required by all modules. For the specific sound modules (e.g., sb.o for the Soundblaster), read the documentation on that module to determine what options are available, for example IRQ, address, DMA. Warning, the options for different cards sometime use different names for the same or a similar feature (dma1= versus dma16=). As a last resort, inspect the code (search for MODULE_PARM). Notes: 1. There is a new OpenSource sound driver called ALSA which is currently under development: http://www.alsa-project.org/ I have not tried it nor am I aware of its status, but it is currently under development. 2. The commercial OSS driver may be obtained from the site: http://www/opensound.com. This may be used for cards that are unsupported by the kernel driver, or may be used by other operating systems. 3. The enlightenment sound daemon may be used for playing multiple sounds at the same time via a single card, eliminating some of the requirements for multiple sound card systems. For more information, see: http://www.tux.org/~ricdude/EsounD.html The "esd" program may be used with the real-player and mpeg players like mpg123 and x11amp. Building the Modules: ===================== This document does not provide full details on building the kernel, etc. The notes below apply only to making the kernel sound modules. If this conflicts with the kernel's README, the README takes precedence. 1. To make the kernel sound modules, cd to your /usr/src/linux directory (typically) and type make config, make menuconfig, or make xconfig (to start the command line, dialog, or x-based configuration tool). 2. Select the Sound option and a dialog will be displayed. 3. Select M (module) for "Sound card support". 4. Select your sound driver(s) as a module. For ProAudio, Sound Blaster, etc., select M (module) for OSS sound modules. [thanks to marvin stodolsky ]A 5. Make the kernel (e.g., make dep ; make bzImage), and install the kernel. 6. Make the modules and install them (make modules; make modules_install). INSMOD: ======= If loading via insmod, the common modules must be loaded in the order below BEFORE loading the other sound modules. The card-specific modules may then be loaded (most require parameters). For example, I use the following via a shell script to load my SoundBlaster: SB_BASE=0x240 SB_IRQ=9 SB_DMA=3 SB_DMA2=5 SB_MPU=0x300 # echo Starting sound /sbin/insmod soundcore /sbin/insmod soundlow /sbin/insmod sound # echo Starting sound blaster.... /sbin/insmod uart401 /sbin/insmod sb io=$SB_BASE irq=$SB_IRQ dma=$SB_DMA dma16=$SB_DMA2 mpu_io=$SB_MP When using sound as a module, I typically put these commands in a file such as /root/soundon.sh. MODPROBE: ========= If loading via modprobe, these common files are automatically loaded when requested by modprobe. For example, my /etc/conf.modules contains: alias sound sb options sb io=0x240 irq=9 dma=3 dma16=5 mpu_io=0x300 All you need to do to load the module is: /sbin/modprobe sb Sound Status: ============= The status of sound may be read/checked by: cat /proc/sound cat /dev/sndstat cat (anyfile).au >/dev/audio The status of the modules and which modules depend on which other modules may be checked by: /sbin/lsmod /sbin/lsmod should show something like the following: sb 26280 0 uart401 5640 0 [sb] sound 57112 0 [sb uart401] soundlow 208 0 [sound] soundcore 1968 8 [sb sound] Removing Sound: =============== Sound may be removed by using /sbin/rmmod in the reverse order in which you load the modules. Note, if a program has a sound device open (e.g., xmixer), that module (and the modules on which it depends) may not be unloaded. For example, I use the following to remove my Soundblaster (rmmod in the reverse order in which I loaded the modules): /sbin/rmmod sb /sbin/rmmod uart401 /sbin/rmmod sound /sbin/rmmod soundlow /sbin/rmmod soundcore When using sound as a module, I typically put these commands in a script such as /root/soundoff.sh. Removing Sound for use with OSS: ================================ If you get really stuck or have a card that the kernel modules will not support, you can get a commercial sound driver from http://www.opensound.com. Before loading the commercial sound driver, you should do the following: 1. remove sound modules (detailed above) 2. remove the sound modules from /etc/conf.modules 3. move the sound modules from /lib/modules//misc (for example, I make a /lib/modules//misc/tmp directory and copy the sound module files to that directory). Multiple Sound Cards: ===================== The sound drivers will support multiple sound cards and there are some great applications like multitrack that support them. Typically, you need two sound cards of different types. Note, this uses more precious interrupts and DMA channels and sometimes can be a configuration nightmare. I have heard reports of 3-4 sound cards (typically I only use 2). On my machine I have two sound cards (cs4232 and Soundblaster Vibra 16). By loading sound as modules, I can control which is the first sound device (/dev/dsp, /dev/audio, /dev/mixer) and which is the second. Normally, the cs4232 (Dell sound on the motherboard) would be the first sound device, but I prefer the Soundblaster. All you have to do is to load the one you want as /dev/dsp first (in my case "sb") and then load the other one (in my case "cs4232"). If you have two cards of the same type that are jumpered cards or different PnP revisions, you may load the same module twice. For example, I have a SoundBlaster vibra 16 and an older SoundBlaster 16 (jumpers). To load the module twice, you need to do the following: 1. Copy the sound modules to a new name. For example sb.o could be copied (or symlinked) to sb1.o for the second SoundBlaster. 2. Make a second entry in /etc/conf.modules, for example, sound1 or sb1. This second entry should refer to the new module names for example sb1, and should include the I/O, etc. for the second sound card. 3. Update your soundon.sh script, etc. Warning: I have never been able to get two PnP sound cards of the same type to load at the same time. I have tried this several times with the Soundblaster Vibra 16 cards. OSS has indicated that this is a PnP problem.... If anyone has any luck doing this, please send me an E-MAIL. PCI sound cards should not have this problem.a Since this was originally release, I have received a couple of mails from people who have accomplished this! Sound Problems: =============== First RTFM (including the troubleshooting section in the Sound-HOWTO). 1) If you are having problems loading the modules (for example, if you get device conflict errors) try the following: A) If you have Win95 or NT on the same computer, write down what addresses, IRQ, and DMA channels those were using for the same hardware. You probably can use these addresses, IRQs, and DMA channels. You should really do this BEFORE attempting to get sound working! B) Check (cat) /proc/interrupts, /proc/ioports, and /proc/dma. Are you trying to use an address, IRQ or DMA port that another device is using? C) Check (cat) /proc/sys/pnp (if this exists, you may need a kernel patch to get this device). D) Inspect your /var/log/messages file. Often that will indicate what IRQ or IO port could not be obtained. E) Try another port or IRQ. Note this may involve using the PnP tools to move the sound card to another location. Sometimes this is the only way and it is more or less trial and error. 2) If you get motor-boating (the same sound or part of a sound clip repeated), you probably have either an IRQ or DMA conflict. Move the card to another IRQ or DMA port. This has happened to me when playing long files when I had an IRQ conflict. 3. If you get dropouts or pauses when playing high sample rate files such as using mpg123 or x11amp/xmms, you may have too slow of a CPU and may have to use the options to play the files at 1/2 speed. For example, you may use the -2 or -4 option on mpg123. You may also get this when trying to play mpeg files stored on a CD-ROM (my Toshiba T8000 PII/366 sometimes has this problem). 4. If you get "cannot access device" errors, your /dev/dsp files, etc. may be set to owner root, mode 600. You may have to use the command: chmod 666 /dev/dsp /dev/mixer /dev/audio 5. If you get "device busy" errors, another program has the sound device open. For example, if using the Enlightenment sound daemon "esd", the "esd" program has the sound device. If using "esd", please RTFM the docs on ESD. For example, esddsp may be used to play files via a non-esd aware program. 6) Ask for help on the sound list or send E-MAIL to the sound driver author/maintainer. 7) Turn on debug in drivers/sound/sound_config.h (DEB, DDB, MDB). Configuring Sound: ================== There are several ways of configuring your sound: 1) Hardcoded in the kernel at compile time (not applicable when using sound modules). This was the OLD way! 2) On the command line when using insmod or in a bash script using command line calls to load sound. 3) In /etc/conf.modules when using modprobe. 4) Via Red Hat's /usr/sbin/sndconfig program (text based). 5) Via the OSS soundconf program (with the commercial version of the OSS driver. And I am sure, several other ways. Anyone want to write a linuxconf module for configuring sound? For More Information (RTFM): ============================ 1) Information on kernel modules: linux/Documentation/modules.txt and manual pages for insmod and modprobe. 2) Information on PnP, RTFM manual pages for isapnp. 3) Sound-HOWTO and Sound-Playing-HOWTO. 4) OSS's WWW site at http://www.opensound.com. 5) All the files in linux/Documentation/sound. 6) The comments and code in linux/drivers/sound. 7) The sndconfig and rhsound documentation from Red Hat. 8) The Linux-sound mailing list: sound-list@redhat.com. 9) Enlightenment documentation (for info on esd) http://www.tux.org/~ricdude/EsounD.html. 10) ALSA home page: http://www.alsa-project.org/ Contact Information: ==================== Wade Hampton: (whampton@staffnet.com)